Construction equipment

Industrial Dewatering Pumps

1 product

A construction pump is chosen for the liquid, not for the size of the job. Rainwater, water carrying sand, slurry with stones and sewage are four different tasks — and four different builds, none of which a single "more powerful" machine can replace.

1 product

Manufacturer, not a middleman Toolsa machines are ours — we know them from the design side, not from a catalogue.
Service and parts on site Wearing parts stay in our warehouse — the machine does not wait for a delivery from abroad.
Dispatch with a real date Every item shows the delivery day, not “24–48 h”.
Matched to your site Tell us the layer and the area — we will match the machine and the tooling. +48 732 081 091

Hence the split. Clean water pumps lift clean water to 60 m. Submersible pumps dewater excavations of contaminated water and draw down to 2 mm. Trash pumps with Honda engines move slurry and large volumes with no mains supply. Sewage is handled by submersibles with an agitator.

The second criterion is supply: 230 V from a socket, 400 V from a distribution board, or a petrol engine where there is no power at all. On an excavation that answer settles the matter before any hydraulic figure does.

Read moreShow less

Fire hoses and fittings are in pump accessories — and they, rather than the pump itself, most often decide the real output of the system.

Four tasks, four builds

Clean water — booster pumps

Lifting water from a well, tank or system to heads measured in tens of metres: 50–60 m on these machines through 25 and 40 mm outlets. Narrow lines and a tall column — the exact opposite of dewatering. Here solids are a problem rather than the norm.

Contaminated water — submersible pumps

An excavation after rain, water carrying sand, turbid seepage. The pump works immersed, so it needs no priming, and the TAX series draws down to 2 mm — effectively dry. Heads are low, 6–10 m, because the water is discharged beside the pit rather than onto a roof.

Slurry and large volumes — trash pumps

Material with solids and stones, with no electrical supply. Honda GX 160, GX 270 and GX 390 engines, outlets from 2" to 4", heads of 26–29 m. This is the only family that works on a site with no distribution board.

Sewage — submersibles with an agitator

Liquid with sediment that settles on the bottom. An agitator at the inlet keeps it in suspension so the pump lifts it instead of drawing the water off the top. Heads of 15 and 30 m, because sewage is lifted into an existing installation.

Every Toolsa pump in one comparison

Family Liquid Max head Outlet Supply Category
TAPM · TAAMG clean water 50–60 m 25 · 40 mm 230 V clean water pumps
TAX contaminated water 6–10 m 2" 230 V submersible pumps
TAPWA sewage, sediment 15–30 m 2" 230 / 400 V submersible pumps
TA-HLS slurry, large volumes 26.3–29.1 m 2" · 3" · 4" petrol (Honda) trash pumps

The comparison shows a relationship that individual data sheets hide: the dirtier the liquid, the larger the outlet and the lower the head. A clean water pump lifts 60 m through a 25 mm line; a trash pump moves material through a 4" outlet but will not reach beyond thirty metres. That is not a difference in quality but in physics — large particles need a large bore, and a large bore lowers achievable pressure.

Supply decides before hydraulics do

On site the first question is what can actually be plugged in. 230 V pumps — the whole TAX series and the smaller booster pumps — run from any socket, and they cover most dewatering work.

400 V appears where power exceeds what a single-phase installation can carry: here that means the 2.2 kW sewage pump with 30 m of head. Without a distribution board on site that machine is unusable whatever its specification.

A petrol engine answers the absence of electricity, not a shortage of power. A trash pump works in a field, during an outage and anywhere the supply is yet to be built — at the cost of noise, exhaust, and the fact that it must never be started in an enclosed space.

How to choose a pump

Start from what is in the water

That question settles the family, and the family narrows the choice to a few models. Clean water, water with sand, settled sediment and slurry with stones need four different builds. A pump chosen for cleaner duty than it gets blocks within the hour; one chosen for dirtier duty will not reach the head required.

Measure the level difference, not the depth

Head runs from the liquid surface to the discharge point. The quoted maximum is reached at zero flow, so real output is read at your own head — the full explanation is in submersible excavation pumps.

Check the supply before the specification

A 230 V socket, a 400 V board, or no power at all — that answer narrows the range faster than any hydraulic figure and saves you weighing up a machine you could not start.

Count the hose with the pump

A hose narrower than the outlet takes away most of the output while the pump runs perfectly normally and shows no sign of a fault. Diameter and length are chosen with the machine — covered in pump accessories.

Questions and answers

Which construction pump for which water?

The type of liquid decides, not the size of the job. Clean water from a well or tank means booster pumps with 50–60 m of head. Contaminated water in an excavation means submersibles of the TAX series, drawing down to 2 mm. Liquid with sediment and sewage need a pump with an agitator. Slurry with stones, and work without electricity, means trash pumps with Honda engines and outlets from 2" to 4".

Why does a slurry pump lift lower than a clean water pump?

Because large particles need a large bore, and a large bore lowers achievable pressure. A clean water pump lifts 60 m through a 25 mm line; a trash pump moves material through a 4" outlet but reaches under thirty metres. That is not a difference in quality but in physics — which is why one machine cannot replace both, whatever its engine rating.

Which pump for dewatering an excavation?

A submersible rated for contaminated water — the TAX series: 0.6 or 0.8 kW, a 2" outlet, 6 or 10 m of head. Two features matter besides flow: suction down to 2 mm, effectively dry, and a float switch that stops the pump once the water has gone and protects it from running without cooling. Selection detail is in submersible excavation pumps.

What is the difference between a submersible and a trash pump?

How they work and how they are powered. A submersible runs immersed, needs no priming and draws down to a few millimetres, but requires electricity and lifts 6–30 m. A trash pump stands beside the water, draws through a suction hose, runs a petrol engine and moves large volumes with solids — it works where there is no power at all. It must never be started in an enclosed space.

What supply do construction pumps need?

Most run from a 230 V socket — the entire TAX submersible series and the smaller booster pumps. A 400 V supply is required by the 2.2 kW sewage pump with 30 m of head; without a distribution board on site it is unusable whatever its specification. Trash pumps need no electricity at all, and that, rather than engine power, is their real advantage.

Will a pump handle sand and stones?

Sand in suspension is handled by the TAX submersible series. Sediment already settled into a layer needs the version with an agitator, because an ordinary pump draws the water off the top and leaves the solids in place. Stones and large solids are the province of trash pumps, which have the bores for it, from 2" to 4". A clean water pump is not intended for any of these duties.

Why does the pump not reach its stated flow?

Because maximum flow and maximum head never occur together: the first at zero head, the second at zero flow. Real duty sits between them. The second cause is usually the hose — narrower than the outlet, or folded over the edge of an excavation, it takes away most of the output while the pump runs normally. Both mechanisms are covered in submersible excavation pumps and pump accessories.

How much water is left after pumping?

It depends on the build. TAX submersibles draw down to 2 mm, so only a film remains, cleared with a wet and slurry vacuum or by hand. Pumps without that feature stop drawing at a few centimetres. A trash pump standing beside the excavation always leaves more, because it is limited by suction lift and by where the strainer sits.

Subcategories and related equipment

Clean water and domestic systems are clean water pumps; excavation dewatering and sewage are submersible excavation pumps; slurry and work without power are trash pumps. Fire hoses and fittings are in pump accessories. Residual water on a floor is picked up by wet and slurry vacuums.